FreeSource : Comment 846

This is a comment on Soft Ware / Системы Биллинга И Учёта Трафика, posted by k152-25.saltov.net at 2006-04-17 01:35:47

Free Nibs?+Freedadius+MPD:ошибка 691, при конекте из под Винды
[b]Помогите плизз![/b]
Привет.
ОС: Free BSD 6?.0
Выпадает ошибка 691, при конекте из под Винды – включал/выключал шифрование.
mpd v4
Использую Веб-интерфейс: nibs_web(.tar.bz2)
Нибс: freenibs-0.0.3-bf3_freeradius-1.0.1(.tar.bz2)
Радиус:freeradius-1.0.1(.tar.gz)
Использовал для ДБ: nibs_mysql_prof_add.sql,nibs_mysql_cards.sql,nibs_mysql.sql из freenib's
fireWall:pf
Пользователи не могут подключится...!
Если это ошибка не в настройках – то скажите!!!
Я тогда посижу над интерфейсом...
[b]А лутше прислать дамп рабочей базы даных[/b]
weldpua2008@ukr.net
Привожу свои настройки:
#cat acct-users
DEFAULT

Service-Type == Framed-User,
Service-Type == Login-User,
Login-Service == Telnet,
Login-Service == Rlogin,
Login-Service == TCP-Clear,
Login-TCP-Port <= 65536,
Framed-IP-Address == 255.255.255.254,
Framed-IP-Netmask == 255.255.255.255,
Framed-Protocol == PPP,
Framed-Protocol == SLIP,
Framed-Compression == Van-Jacobson-TCP-IP,
Framed-MTU >= 576,
Framed-Filter-ID =* ANY,
Reply-Message =* ANY,
Proxy-State =* ANY,
Session-Timeout <= 28800,
Idle-Timeout <= 600,
Port-Limit <= 2

#cat huntgroups |grep -v '#'
vpn NAS-IP-Address == 192.168.10.1
# cat radius.conf
acct 127.0.0.1 weldpua 3 2
auth 127.0.0.1 weldpua 3 2

radiusd.conf – не трогал
# cat clients
192.168.10.1 weldpua
127.0.0.1 weldpua
# cat clients.conf
client 127.0.0.1 {

secret= weldpua
shortname = localhost
nastype = other # localhost isn't usually a NAS...

}

client 192.168.10.1 {

secret = weldpua
shortname = localhost
nastype = other # localhost isn't usually a NAS...

}

# cat hints
DEFAULT Suffix = “.ppp”, Strip-User-Name = Yes

Hint = “PPP”,
Service-Type = Framed-User,
Framed-Protocol = PPP

DEFAULT Suffix = “.slip”, Strip-User-Name = Yes

Hint = “SLIP”,
Service-Type = Framed-User,
Framed-Protocol = SLIP

DEFAULT Suffix = “.cslip”, Strip-User-Name = Yes

Hint = “CSLIP”,
Service-Type = Framed-User,
Framed-Protocol = SLIP,
Framed-Compression = Van-Jacobson-TCP-IP

# cat naslist
192.168.10.1 local portslave
127.0.0.1 local other

# cat nibs.conf|grep -v '#'
nibs {

driver = “rlm_nibs_mysql”
server = “localhost”
port = “3306”
login = “root”
password = ""
nibs_db = “freenibs”

....остальное без изменений

# cat /usr/local/etc/mpd4/mpd.conf
default:

load pptp0

pptp0:

new -i ng00 pptp0 pptp0
set ipcp ranges 192.168.10.1/24 192.168.11.1/32
load pptp_standart

pptp_standart:

set iface disable on-demand
set bundle enable multilink
set link yes acfcomp protocomp
set link no pap chap
set link enable chap
set link keep-alive 60 180
set ipcp yes vjcomp
set ipcp dns 192.168.10.1
set iface enable proxy-arp
set bundle enable compression
set ccp yes mppc
set ccp yes mpp-e40
set ccp yes mpp-e56
set ccp yes mpp-e128
set ccp yes mpp-stateless
set bundle yes crypt-reqd
set pptp enable incoming
set pptp disable originate
set iface mtu 1500
set link mtu 1500
set radius server 127.0.0.1 weldpua 1812 1813
set radius timeout 10
set radius config /opt/freeradius1.0.1/etc/raddb/radius.conf
set radius retries 3

# ifconfig
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500

options=8<VLAN_MTU>
inet 192.168.10.1 netmask 0xffffff00 broadcast 192.168.10.255
ether 00:0e:2e:2f:84:68

rl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500

options=8<VLAN_MTU>
inet 192.168.129.146 netmask 0xfffff000 broadcast 192.168.143.255

plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1500
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33208
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384

inet 127.0.0.1 netmask 0xff000000

pfsync0: flags=0<> mtu 2020
ng0: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500

inet6 fe80::20e:2eff:fe2f:8468%ng0 prefixlen 64 scopeid 0x7